Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Rockwall
Gate parts and welding in Rockwall means dealing with two forces that work against iron every season: the expansive black clay under your posts and the lake air off Ray Hubbard. A gate that dragged after spring rain, a hinge that seized near Chandler’s Landing, a slide gate that jumped its rollers on a shared driveway, these are the calls we run week after week. Our Gate Parts & Welding crews know Rockwall’s soils and subdivisions and stock the hinges, rollers, posts, and weld material to fix the gate on the first visit. Call (936) 715-3043 and a live person answers, day or night.
Why Ironworks Gate Co. Is Rockwall’s Preferred Gate Parts & Welding Company
Since 1984, Ironworks Gate Co. has built its name the slow way: show up when promised, quote a fair price before turning a bolt, and stand behind the work in writing. Rockwall homeowners call us because the generalist handyman does not carry a stick welder in his truck and does not know why a Viking operator arm strips on a post that has canted two degrees. We do. Our technicians are background-checked, uniformed, and trained on nine opener brands, LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so the diagnosis is right the first time.
Every job we complete carries the 90-Day Done Right Promise. It is written, no paperwork, no arguing. If it is not right, we come back and make it right. Rockwall residents also get our standing offers: $50 off any repair over $250, a free second opinion on any written estimate, an $89 seasonal tune-up, and a permanent 5% senior and veteran discount. Victor Salinas, our owner, set the standard that the 400th job gets the same care as the first.
Our Gate Parts & Welding Services in Rockwall
Hinge Replacement
Rockwall’s ornamental iron gates eventually show their age at the hinges first. The lake moisture along Chandler’s Landing and The Shores accelerates rust on the pin and barrel until the gate begins to drop and drag. We cut out the seized hinge, weld a new steel or stainless pin in place, and re-hang the panel so it swings level. Price for a typical two-hinge replacement in Rockwall runs $240 to $480.
Post Replacement
The black clay under Rockwall is the real story. After wet years it swells. After drought it shrinks. The result is a gate post out of plumb, often by two or three degrees, enough to bind a panel or side-load an operator arm until the motor burns out. We dig the footing, set a new steel post in concrete below the frost line, and weld the hinge brackets back on before re-hanging the gate. A full post replacement in Rockwall typically runs $350 to $700 per post, including concrete.
Rail Repair
Sliding gates on Rockwall’s narrow side yards and shared driveways fail at the bottom rail. Rust works through the tube, the gate sags, and the rollers bind until the panel derails. We cut out the rotted section and weld in new steel, then true the track so the gate rides smooth. Most rail repairs run $180 to $360 in Rockwall, depending on the length of rot.
Custom Welding
Sometimes the gate is worth saving but the ornament is broken: a scroll snapped, a picket cracked, a latch mount torn from the frame. Our welding bench handles those. We hot-roll replacement steel to match the existing profile, weld it in, and grind the joint flush so the repair disappears under paint. Custom welding on Rockwall estate gates typically runs $150 to $400 per section, quoted before work starts.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Rockwall
We carry parts for the operators Rockwall homes actually have: LiftMaster, DoorKing, Elite, Viking, and more. When a Ghost Controls arm shears or a Mighty Mule board fails, we stock or can quickly source the exact part for a same-week fix. And because we weld on site, we can often repair a bracket or fabricate a missing mounting plate that a parts catalog cannot solve. Call (936) 715-3043 for a free estimate on any brand.
Common Gate Parts & Welding Problems We See in Rockwall Homes
- Post heave after rain. The clay under Rockwall County swells with every wet season. A post that was plumb last fall is now canted, the gate panel drags against the rack and pinion or drag shoe, and the operator strips its gears trying to force it. We reset the post and re-hang the gate before the motor dies.
- Lakefront hinge corrosion. Homes along Lake Ray Hubbard, especially Chandler’s Landing and the older lakeside streets, see surface rust that inland Rockwall does not. Hinge pins seize, roller brackets rust through, and the gate jerks before it stalls. We replace with galvanized or powder-coated hardware.
- Slide-gate derailments on shared driveways. Rockwall’s narrow side yards and shared access easements force many homes into sliding configurations. A rusted bottom rail or failed roller bearing drops the panel off the track and blocks the driveway. That is a repair we make same-day when possible.
- Operator arms under side-load. A canted post is not just a structural issue. It side-loads the operator arm for months or years until the motor burns out. If we replace the motor without fixing the post, the new one fails too. In Rockwall we fix the structural cause first.
Pricing for Gate Parts & Welding in Rockwall, TX
Rockwall pricing runs close to the metro norm, with a few lakefront adders. Hinge replacement typically runs $240 to $480. A new gate post, set in concrete and welded, is $350 to $700. Bottom rail repair on a slide gate is $180 to $360. Custom welding work is $150 to $400 per section. Operators: a new arm or gear kit runs $180 to $340, while a full operator replacement, depending on swing versus slide and brand, runs $850 to $2,400 installed. The price you are quoted is the price you pay, settled before any work starts. Estimates are free, and the $89 seasonal tune-up catches small welds and roller wear before they become big ones. Call (936) 715-3043 for an exact number.
We Also Serve Cities Near Rockwall
Our crews cover Rockwall and the surrounding communities, including Fate, Royse City, Lavon, and Rowlett. If you live in one of those towns and need gate parts or welding, the same Gate Parts & Welding in Rockwall team handles your neighborhood too. Dispatch and scheduling are coordinated from the brand’s Dallas-Fort Worth office, but the trucks and technicians are local to Rockwall County.
Serving Rockwall, TX - Our Local Coverage Area
We’re based in the Rockwall area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Rockwall
The black clay under Rockwall expands when wet and shrinks when dry, which shoves gate posts out of plumb a little more each cycle. Once the post cants, the panel drags until it binds or the operator burns out. The fix is resetting the post and welding the hinge brackets level, not just adjusting the opener. Call (936) 715-3043 and we will come look at the footing.
Most of the time we can straighten and re-seat a shifted post without replacing it, as long as the steel is not rotted through at the base. We dig around the footing, plumb the post, pour new concrete, and weld the hinge brackets in alignment. If the post is rusted or cracked, replacement is the honest call. Either way you get a written price before we start.
Yes, in most cases. We lift the panel, replace the failed roller bearings or weld a new bottom rail section, and reset it on the existing track. The track itself rarely needs replacing unless it is bent or rusted through. Most roller and rail fixes in Rockwall are done in one visit.
That usually means the post has shifted and the operator arm has been absorbing side-load for months or years. The metal fatigues and eventually shears or bends. We replace the arm and then fix the structural cause, the canted post, before re-connecting the opener. Skip the post fix and you will be back in the same spot next season.
Yes. Automated driveway gates must have photo-eye sensors or contact edges that stop and reverse the gate if a vehicle or person is in the path, and these must function after any repair. When we replace hinges, rollers, or an operator in Rockwall, we test the safety system as part of the job. A gate with a dead sensor is a gate that can hurt someone, and we will not leave it that way. Call (936) 715-3043 for a free safety check with any repair.
If your gate is dragging, rusting, or down, call Ironworks Gate Co. at (936) 715-3043. We will quote the repair before we start, weld what needs welding, and put the 90-Day Done Right Promise on it in writing. Rockwall gate owners have been calling us for 42 years. We plan to be answering the phone for another forty.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Rockwall since 1984.