Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterWhy Rockwall Homeowners Choose Ghost Controls Gate Repair
We provide Ghost Controls in Rockwall as an independent gate repair service for every opener the brand has made worth knowing: the AXDP-1 single-arm kit, the GSL linear swing series, the GTP wireless keypad, and the heavy-duty HDP1 and HDP2 pivot-arm openers. What sets our Ghost Controls work apart is that we diagnose at the board level. Where a dealer might swap an entire AXDP controller for a four-figure replacement, we often restore the same board by reflowing the limit-switch solder joints and replacing the relays, and we stand behind that repair in writing with our 90-Day Done Right Promise. We are not affiliated with or authorized by Ghost Controls. We are an independent service provider in Rockwall with the training and bench experience to fix these systems without factory-dealership constraints. Call (936) 715-3043 any hour, any day, and a live person will answer.
Why Trust Ironworks Gate Co. for Your Ghost Controls Gate Repair?
Victor Salinas, our owner, grew up in Rockwall not far from the old downtown square. He spent enough summers watching his uncle weld fence sections to know he wanted to work with his hands. He trained in welding and industrial maintenance at Eastfield College in Mesquite, then spent close to three decades doing Gate Repair across Rockwall County, including Ghost Controls systems that other shops had already given up on. That background matters when your Ghost Controls opener is doing something strange at six in the morning and you need a straight answer, not a parts cannon.
Our technicians know the AXDP, GSL, and HDP board generations well enough to tell you which failure is electrical, which is mechanical, and which is both. We use genuine Ghost Controls boards, arms, and accessories whenever the owner wants factory-spec operation. We also carry quality aftermarket limit-switch and power-supply components for older out-of-warranty units where the OEM part costs more than the job is worth. Every repair is quoted and agreed before any work starts, and every completed job carries the 90-Day Done Right Promise. No paperwork. No arguing. If it is not right, we come back and make it right.
Common Ghost Controls Gate Repair Problems We Fix in Rockwall
Ghost Controls builds a solid opener, but certain failures show up again and again near Ghost Controls repair in Fate and throughout Rockwall, particularly on gates installed 10 to 18 years ago. Here are the five we see most often:
- Random gate reversals or mid-travel stops (AXDP series). The most common cause is a failing limit-switch solder joint on the AXDP control board. The joint develops a hairline crack that opens when the board warms up, so the gate runs fine in the morning and starts acting up by mid-afternoon. We reflow those joints at our bench and the board usually stays reliable for years.
- Water intrusion in the GSL linear arm boot. The rubber boot on the GSL series linear arm is a good design, but after years of North Texas sun it can crack or pull loose at the collar, letting moisture into the gearbox. That leads to internal gear corrosion and a grinding sound during travel. If the scoring is not too deep, we seal, regrease, and re-boot the arm. If the gearbox is chewed up, we replace the arm.
- Dead wireless keypad after battery replacement (GTP). The GTP keypad is notorious for losing its pairing to the control board when the battery dies completely. The owner puts in fresh batteries, the keypad lights up, and nothing happens. We re-pair the keypad to the board and verify the range before we leave.
- Slave gate drift on double-swing installations. This happens when the two boards are from different AC/DC revisions, something we see on older HDP-series double installs where one board was replaced at some point. The slave gate slowly falls out of sync over a few weeks. The fix is matching the board revisions and re-setting the travel limits for both leaves.
- Overload clutch slipping on HDP1/HDP2 pivot arms. The clutch spring inside the pivot arm weakens with age, and the gate will start opening halfway and reversing in the afternoon heat, when the metal expands and the load changes just enough. We replace the overload clutch spring and re-set the force limits, which is a fraction of the cost of a new arm.
Ghost Controls Parts & Our Repair-vs-Replace Approach
We make the repair-versus-replace call the way we would for our own driveway. If your AXDP board has two bad relays and nothing else wrong, we rebuild the relay section and send you home with a working controller for a couple hundred dollars instead of a full board replacement. If your GSL arm is grinding because water got past the boot, we open the gearbox and inspect the gear faces before we order anything. A seal and regrease is a legitimate repair. Scored gears are not. We replace a GSL arm only when the gearbox is damaged beyond a simple seal-and-regrease, and we rebuild AXDP boards when the damage is confined to relays.
For Rockwall customers who want factory-spec operation, we order genuine Ghost Controls parts direct. For older units out of warranty, we stock quality aftermarket limit-switch and power-supply components that get a gate running the same day without the OEM wait. You will know exactly what we are installing and what it costs before we turn a single screw. Call (936) 715-3043 for an honest assessment and a written quote.
Our Ghost Controls Service Process - Step by Step
You should know exactly what happens when we pull up to your Rockwall driveway. Here is the sequence, the same on every Ghost Controls job:
- 1
Diagnosis. We test the board, the arm, the receiver, the keypad, and the safety edges as one system, not as isolated parts. We pay particular attention to limit-switch behavior on AXDP boards and boot integrity on GSL arms, because those are the two places where Ghost Controls failures hide.
- 2
The quote. We walk you through what we found, what it costs to fix, and what it costs to replace if repair is not worth it. The price is set before any work begins. No surprises on the bill.
- 3
The repair or installation. We rebuild or replace the board, re-boot and regrease the arm, re-pair the keypad, reset travel limits, and recheck the force settings. Structural work, like resetting a post that has shifted in Rockwall’s clay soil, happens before operator work so the opener is not fighting a bound gate.
- 4
Testing. We cycle the gate ten times or more, including a test in both directions with the safety edges triggered. We check the remote range from the street and from inside the house. The gate is not done until it closes like the day it was hung.
- 5
Warranty. Every job leaves with the 90-Day Done Right Promise in writing. If anything we touched acts up within 90 days, we come back and fix it. No paperwork, no arguments.
Ghost Controls Products We Service & Install in Rockwall
We service and install the full Ghost Controls lineup that matters to Rockwall homeowners: the AXDP-1 single gate opener kit, the GSL (Ghost Swing Linear) series arms, the GTP wireless keypad, and the HDP1/HDP2 heavy-duty pivot arm openers. That covers single and double swing gates, from lightweight ornamental iron to heavy estate panels.
We keep common Ghost Controls consumables in local stock: remote transmitters, keypad batteries and mounts, limit-switch assemblies, boot collars, and power-supply capacitors. That means most Rockwall Ghost Controls repairs are completed in a single visit, not a week of waiting on a backordered part. For anything we do not have on the truck, our parts suppliers run same-week delivery to the Rockwall area.
We Also Service These Brands
Ghost Controls is one of nine gate-automation brands we are trained and equipped to service, alongside LiftMaster, Mighty Mule, DoorKing, FAAC, BFT, Linear, Viking, and Elite. If your Rockwall property has a different opener on a second gate, or you inherited a mixed-brand setup near Ghost Controls in Crandall, one call covers all of it.
FAQs - Ghost Controls Gate Repair Service in Rockwall
These are the questions Rockwall Ghost Controls owners ask us most often. Straight answers first, then the number to call.
Three beeps on a Ghost Controls system typically means the control board is sensing an obstacle or a short in the safety circuit, but it can also indicate a failed limit switch on the AXDP board. The gate is refusing to run because the board does not know where the gate is, so it defaults to safe mode. We test the limit-switch continuity and the safety-edge wiring to isolate which one is triggering the alarm. Call (936) 715-3043 and we will talk you through what to check before we even roll a truck.
Yes, in almost every case. Ghost Controls remotes use a rolling-code receiver, and we can either transfer the existing receiver module to the new board or re-pair the remotes to the new receiver in about five minutes. You will not need to buy new remotes just because the board was replaced. Bring every remote you own to the appointment, including the one in the kitchen drawer, and we will have them all programmed before we leave.
When the keypad works but the remote does not, the problem is almost always in the receiver module or the remote’s programming, not the main control board. Most often the receiver has lost its memory or the remote’s rolling code has fallen out of sync after sitting unused. We re-pair the remote to the receiver, and if the receiver itself has failed, we replace the module rather than the entire board. That is a much smaller repair than most people expect. Call (936) 715-3043 and we will quote it over the phone.
Drifting sync on a double-swing Ghost Controls installation generally means the two boards are running mismatched AC/DC revisions, or the travel limits were never set cleanly after one side was serviced. We match the board revisions, re-set both travel limits, and re-check the force settings so the leaves open and close together every cycle. If the drift is coming from a slave gate sensing a slight voltage difference, we correct that at the board level rather than masking it with programming tricks.
Yes, in most cases. Ghost Controls made retrofit battery-backup kits for several of their older slide and swing lines, and where the factory kit is no longer available, we can install a compatible aftermarket backup system that is properly fused and wired. A battery backup on a Ghost Controls slide opener gives you roughly 20 to 30 cycles during a power outage, which is enough to get cars in and out without getting out in the rain. Call (936) 715-3043 and we will tell you whether your specific model can take one and what it costs.
Most Ghost Controls repairs in Rockwall run between $180 and $450, depending on whether we are rebuilding a board, replacing an arm, re-pairing a keypad, or resetting posts that have shifted in the clay soil. A limit-switch reflow on an AXDP board is usually under $200. A GSL arm replacement with labor typically runs $350 to $500. A full AXDP board replacement when rebuild is not possible runs $400 to $700 installed. Every job is quoted and agreed before work starts. Call (936) 715-3043 for an exact quote, and ask about our current offers: $50 off any repair over $250, a free second opinion on any written estimate, an $89 seasonal tune-up, and a permanent 5% senior and veteran discount.
Book Your Ghost Controls Service in Rockwall, TX
If your Ghost Controls gate is opening halfway, reversing on its own, or dead at the keypad, call (936) 715-3043. A live person answers 24 hours a day, seven days a week. We will schedule a time that works, show up when we say, and hand you a written price before any work begins. Done right, and backed in writing.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Rockwall since 1984. If the gate doesn’t work right, nothing else about it matters.