FAAC Gate Parts & Welding Nationwide

FAAC Gate Parts & Welding in Rockwall: What to Know First

FAAC gate parts and welding in Rockwall comes down to matching the right component to the right model, then making sure the weld holds through Texas heat and clay-soil movement. We stock common FAAC hinges, brackets, and mount assemblies, and most repairs are completed in a single visit. Pricing is straightforward: you get a firm quote before any work begins, and the number we give you is the number you pay.

Call (936) 715-3043

This page is for Rockwall homeowners running a FAAC swing or slide operator who’ve hit a mechanical failure: a snapped hinge, a cracked post, a rail that’s out of square, or a latch that no longer catches. If that sounds familiar, call (936) 715-3043. A live person answers, day or night, and we’ll talk you through what’s likely going on before we ever send a truck.

How FAAC Products Fail - and How We Fix Them

FAAC builds a solid operator, and we’ve worked on enough of them across Rockwall to know their habits. Here’s what we see in driveways around town, model by model:

• Hinge welds breaking loose on FAAC swing gate leafs: The C720 and C721 series put real torque into the gate leaf, and any play in the hinge transfers that force straight into the weld. In Rockwall’s clay soil, posts shift seasonally, the leaf sags a quarter inch, and the stress concentrates on the bottom hinge bracket. We cut out the old weld, true the leaf back to level, and weld in a gusseted bracket that spreads the load instead of focusing it on one bead.
• Post fatigue on the 760/770 series: These hydraulic operators move a lot of weight, and they push against the post on every cycle. After years of that, we see posts cracking at the base plate or leaning just enough to throw the operator’s geometry off. We replace the post, set it deeper than the original, and weld the mount plate flat so the piston isn’t fighting a crooked anchor.
• Rail drift on FAAC slide gate tracks: The 844 series slide operators want a straight, level rail. When the rail shifts even half an inch, the gate starts chattering against the rollers and the operator’s strain increases. We realign the rail, weld the splice plates properly, and verify the roller contact before we call the job done.
• Latch and lock misalignment after a storm: Rockwall gets its share of straight-line wind and hail, which flexes gate frames enough to knock the latch out of line. The FAAC bolt-on latches and mag locks still work fine, but the geometry doesn’t. We refit the latch plate, weld the catch into position, and test it twenty times before we leave.
• Universal aftermarket brackets that don’t actually fit: We’ve repaired more than a few FAAC gates where someone bolted on a generic bracket that fits “most brands.” It doesn’t. FAAC mount plates have specific bolt patterns and torque ratings. We replace the universal part with the correct OEM or OEM-spec bracket and weld it square to the gate frame.

Our FAAC Gate Parts & Welding Process

Every job follows the same discipline, whether it’s a hinge replacement or a full post rebuild. Here’s how a typical FAAC parts and welding call goes in Rockwall:

1. 1
   You call (936) 715-3043. You get a person, not a menu. We ask what the gate is doing, or not doing, and schedule a visit that works for you.
2. 2
   We diagnose on site. Our technician looks at the whole system: operator, brackets, hinges, rail, posts, and electrical. We find the root cause, not just the symptom.
3. 3
   You get a firm price. Before any wrench or welder comes out, we quote the repair in writing. No hourly surprises, no “while we’re here” add-ons unless you approve them first.
4. 4
   We fix it right. OEM part when warranty or fit requires it, quality OEM-spec when it doesn’t. Every weld is ground clean, checked for penetration, and painted or coated to match.
5. 5
   We test the gate under load. Full open, full close, obstruction response, and ten cycles minimum. If it doesn’t run like it should, we stay until it does.
6. 6
   You get the 90-Day Done Right Promise. Written guarantee, no paperwork, no arguing. If it isn’t right, we come back and make it right.

What FAAC Gate Parts & Welding Costs in Rockwall

Straight numbers help, so here they are. These reflect what we charge for common FAAC repairs in Rockwall right now:

• Hinge replacement with welding: $180-$340 per hinge, depending on gate weight and access.
• Post replacement with new concrete and weld plate: $450-$800, depending on post size and depth.
• Rail realignment and splice welding: $200-$400, depending on rail length and condition.
• Latch or lock refit with welding: $150-$300, including parts.
• Custom bracket fabrication for FAAC mount plates: $120-$250, cut and welded to spec on site.

What moves the price is post condition, gate weight, and whether the repair is clean steel or rust-repaired steel. And there are standing offers that apply: $50 off any repair over $250, a free second opinion on any written estimate, and a permanent 5% discount for seniors and veterans. Call (936) 715-3043 for an exact quote. Estimates are free.

Why Rockwall Homeowners Call Ironworks Gate Co. for FAAC Work

We’ve been doing gate work around Rockwall for over 42 years, and the reason people keep calling is simple: we show up when we say we will, tell you what the gate actually needs, and stand behind the work in writing. Victor Salinas, our owner, grew up in Rockwall and still runs the company like the town he remembers: a handshake means something, and a job isn’t done until it’s done right.

If your FAAC operator is down and you need a part welded or a post replaced, we’ll handle it. And because we service nine automation brands, including LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, you won’t have to call someone else if the problem turns out to be more than the weld. One truck, one crew, one guarantee.

FAQs